| |
| Features: Main body with base, drawing drum and drawing die box of close grain Cast Iron Water Cooling arrangement provided inside the Drawing Drum and the Die Box Phosphorous bronze gears with high carbon axle steel worms Suitable for making Nail Wire from 8 mm or 6 mm input rods up to 2 mm Also suitable for making Wire used to make Barbed Wire, Wire Mesh, etc. Wet / Slip type Fine Wire Drawing Machine also available - Details on request |
Operation: The wire rod to be drawn is pointed in the Wire Pointing Machine. This pointed wire is inserted through the die of the first Wire Drawing Machine and fastened to a locking device on the drum. The drum is then started. As the drum rotates, the wire fastened to the drum gets pulled and coiled around the drum. Since the wire getting pulled is passed through the die having a higher inlet diameter and a lower outlet diameter, the drawn wire diameter gets reduced. The starting end of the drawn wire is released from the lock of the first drum, is passed through the overhead loop and pulley provided, is brought down and is inserted through the die of the second drum and drawn through this die for further reduction. Thus, the wire is drawn through all the wire drawing drums of the set in a continuous manner to get the required finished diameter of the wire. |
When
the drum of the last wire drawing machine gets fully loaded with
the drawn wire, the machine will be stopped to unload the finished
material and then restarted. (If one opts for the continuous coiling
machine, the drawing process will not have to be stopped for this
purpose) When the bundle of input rod finishes, the machine should be stopped. The end of this bundle is welded to the end of a new bundle of rod using the butt welding machine. Then the process is to be continued. Also, in case of an accidental snapping of wire in between drums, the snapped ends are welded with the help of the butt welding machine and the process is continued. |
| Model: | WD-750 |
WD-610 |
WD-560 |
WD-460 |
WD-305 |
|
| No. of Blocks: | 1
to 3 |
1
to 6 |
1
to 8 |
1
to 6 |
1
to 10 |
|
| Diameter of Drum (mm): | 750 |
610 |
560 |
460 |
305 |
|
| Material to be Drawn: | Mild
Steel / High Carbon Steel / Non-Ferrous Metals |
|||||
| Inlet Wire Size (mm): | 12 |
8 |
6 |
4 |
2.6 |
|
| Finished Wire size (mm): | 6 |
3.37 |
2 |
1.68 |
0.7 |
|
| Finishing Speed (Machine rpm): | 45 |
110 |
140 |
180 |
380
/ 540 |
|
| Motor (HP): | 1st Block: | 50 |
40 |
30 |
15 |
10 |
| 2nd Block: | 40 |
30 |
25 |
7.5 |
||
| 3rd Block: | 30 |
25 |
10 |
10 |
7.5 |
|
| Rest of the Blocks: | -- |
20 |
10 |
10 |
5 |
|
| Approximate Block Weight (kgs.): | 1850 |
1550 |
1450 |
800 |
500 |
|
 |
Wire
Pointing Machine
|
Butt
Welding Machine
|
 |
|||||||||||||||||||||||||||||
 Control Panel Board Suitable for Multi Blocker Wire drawing machines. Supplied with Voltmeter & Amperemeter for individual blocks. Supplied with Pilot Lamp, Timer, Auxiliary Relay Starters, Contactors, overload Relay, HRC Fuses, etc. Fitted on a M.S. Fabricated cabinet |
 Descaling Attachment Suitable to fit with the first block of the wire drawing machines to remove the scales from the inlet wire rod. |
 Continuous Coiling Device To be fitted to the final block of continuous wire drawing machines. Capable to unload the drawn wire from the continuous system wire drawing system without stopping the machine. Supplied with 20 HP electric motor |
 Pay-Off Stand M. S. Fabricated, double hand movable system Pay-Off Stand. Suitable to feed the wire rods to the first block of the Wire Drawing Machines. |
 Die Polishing Machine Suppiled with 1 HP / 3 Phase electric motor. |
Allied
Accessories
Wire Drawing Dies, Tungsten Carbide Dies, Diamond Pins, Diamond Files, Norbide Powder Wire Drawing Compound |
We
Also Offer....... |
 Nail Making Machine |
 Wire Straightening cum Cutting Machine |
 Rivetting Machines |
 Shaping Machines |
 Hydraulic Pneumatic Accessories |
 Pipe Bending Machines |
 Glass Basins |
 Perforated Sheets |
